Description
Alpine S-W12D2
S-Series 12″ Dual 2 Ohm Subwoofer
Boost your BASS with Alpine S-Series Subwoofers.
Alpine introduces the all-new S-Series Subwoofers, their unique design substantially improves bass output and provides installation versatility.
Available in a twelve, ten and eight-inch each S-Series subwoofer uses a custom-stamped steel frame. These high-strength frames were designed to withstand the rigours of the improved S-Series motor. They have frame leg vents as well as a vented back plate to help cool the subwoofer voice coil and motor parts, plus a shallow design to help fit in smaller spaces.
The S-Series Subwoofers incorporate two strontium ferrite magnets that are stacked together, providing increased motor strength and excursion which ultimately delivers an accurate bass to your music. Installation time will be significantly reduced with the convenient push-type insert terminals with a dual voice coil jumper system. Just strip the speaker insulation at the wire end, then insert the bare wire into the hole of the spring-loaded push terminal. While the concealed mount gasket system creates a clean, finished appearance for any vehicle.
All S-Series subwoofers are compatible with optional grilles (sold separately) to provide added protection to the cone. The grilles feature a mesh design with an S-Series logo badge.
Along with the new 8” woofer, the 10” and 12” S-Series subwoofers have been re-designed from the ground up. The mounting depth of the 10” and 12” subwoofers are almost 1” more shallow than previous models at just over 4.5” for the 10” models and just over 5” for the 12” models, allowing them to fit into a wide variety of installation applications.
The 12” S-Series subwoofers are engineered with an improved voice coil allowing the woofer to benefit from an increased power rating of 600 watts. Match them with the powerful Alpine MRV-M500 mono amplifier for a great subwoofer system.
Optional Grills
All the S-Series subwoofers are compatible with optional grills (Sold Separately) to provide added protection to the cone.
The Grills feature a mech design with an S-Series logo badge.
- KTE-8G for the 8" S-Series Subwoofer
- KTE-10G.2 for the 10" S-Series Subwoofers
- KTE-12G.2 for the 12" S-Series Subwoofers
Sound Garage, where experience makes the difference!
Diaphram
- Material: Pulp/Kevlar Cone
- Design: Reinforced Parabolic Cone Structure with PP/Mica/Talc Dust Cap
Surround
- Design: High Amplitude Multi-Roll (HAMR Surround)
Spider
- Design: Progressive with Reinforced Layer Tinsel Leads
Voice Coil
- Material: 5-Layer DVC Winding on AL Former
- Design: 65mm Voice Coil with High-Temp
- High-Excursion Underhung Voice Coil Configuration
Motor Structure
- Pole Geometry: Airflow Optimized Dual Flare Pole Vent
- Perimeter Venting with Airflow Management System
- Configuration: Double-Stacked Strontium Ferrite Magnets
Frame
- Material: High Strength Steel Frame
Terminals
- Layout: One Side
- Design: 8AWG Push Terminals with VC Configuration Jumpers
Tinsel Leads
- Design: Reinforced Layer Spider Integration
Gasket
- Design: Concealed Mount Gasket
Power Handling
- Power Range: 600W-1800W
- RMS Power Handling: 600W
- Peak Power Handling: 1800W
Dimensions
General
- Frequency Response: 24Hz-200Hz
Recommended Box Enclosures
- Recommended Sealed Box: 0.85 cubic foot (gross volume)
- Recommended Vented Box: 1.71 cubic foot (gross volume), 12.5” x 1” vent area, 16” vent length
Thiele-Small Parameters
- Sensitivity (1W/1m) – SPL
- DC Resistance – Re
- Inductance – Le
- Free Air Resonance – Fs
- Equivalent Stiffness – Vas
- Mechanical Q – Qms
- Electrical Q – Qes
- Total Q – Qts
- Cone Area – Sd
- Linear Excursion – Xmax (1-way)
- Mechanical Travel – Xmech (P-P)
Reviews
There are no reviews yet.